Pulling data off of Eaton RGX, SVX and DG1 drives
Hello, I am relatively new to the NI environment and I have been tasked with figuring out a way to pull operational data and error codes off of the drives on our test stands and integrate that into the...
View ArticleBenchmark Ethernet/IP on LinuxRT
Hi, I'd like to connect a PXI controller running LinuxRT with an AllenBradley PLC through EthernetIP.This setup will replace an existing system that reached its end of life. The PLC system will stay....
View ArticleClik here to view.
Transferring an existing Labview executable file to a new PC
I was asked to transfer an existing application running on a windows 7 machine, to a windows 10 machine. I think I have all the relevant software installed, but when I try to run the .exe, I get the...
View ArticleIs there any method to change adapter mode of eth0 to EtherCAT?
Hi! I'm using sbrio 9651 with customized carrier board.I have to use EtherCAT for my project, but unfortunately my carrier board does not have eth1 port.All the documents say that adapter mode of eth1...
View ArticleClik here to view.
LabVIEW newbie - TCP communications
Hello All! I was posting about error 66 but I realized my mistake. If anyone runs into the issue where your server seems to receive a message from your client but only after the client disconnects and...
View ArticleCan't add EtherCAT Master with sbrio 9651 and LabVIEW 2021
Hi all! I'm trying to control a motor by EtherCAT for my project.I prepared required hardware (sbrio 9651 and it's carrier board) and software (LabVIEW 2021, real time module, FPGA module, CRio driver...
View ArticleIEC 60870-104 communication
Hello, I know others have tried and failed but I thought I could give it a shot too. I am using the example vi for IEC 60870-104 in labview 2017. I have a 60870-104 slave (server) running on another...
View ArticleHelp with EtherCAT ESI upload into cRIO project for Siemens Modular Device...
Hello everyone, I am currently working with the Robox EtherCAT card with a Siemens CU320/S120 dual motor setup and looking for guidance when configuring the ESI in twinCAT and then importing the ESI...
View ArticleEthernetIP connectivity with Beckhoff BK9105
I have a BK9105 and am trying to read/write to the I/O using implicit messaging. I have tried using the EEIP library that others have been able to get working for implicit messaging found at...
View ArticleRest API - Patch implementation in labview
Hello Labview'ns I am trying to update test datas to a database via Rest API . I am able to execute Get, post functionality well. Recently got a requirement to update certain blocks via patch.Could...
View ArticleEtherCAT: assignment of Sync Manager at runtime
I have a third party EtherCAT slave that support the assignment of Sync Manager at runtime. In the EtherCAT standard the object 1C13h establishes the PDO assignment of Sync Manager 3.As for the object...
View ArticleEtherCAT chang PDO mapping
Is it possible to change the PDO mapping of an EtherCAT slave during runtime? the question was already asked in differt post bofore but is not clear yet is if is possible or not.
View ArticleDNP3 set individual point variation
I'm implementing an outstation following an interface that includes Analog inputs with all but one of the variations as single precision with flags (obj 30:var 5). Then there is one point requiring 16...
View ArticleS7 Communication with TPC-2230
Hi, I'm looking into the technical feasibility of setting up a Siemens S7-1200 PLC as my main controller, with an NI TCP-2230 as the front-end HMI. Can this be accomplished by adding the Touch Control...
View ArticleInvertek Optidrive Modbus Communication issues using Minimal Modbus on and RPI3
I'm am controlling an OPTIdrive e from an RPI3 running minimal modbus I can read and write the all RTU registers except RTU-1, the control word, correctly by subtracting 1 from the Optidrive RTU...
View ArticleOpen source EtherCAT library for Linux
Anyone successfully did an EtherCAT Master under Linux and used a library under LabVIEW to communicate with SDOs and PDOs? I would basically try to do so without using the "NI-Industral Communications...
View ArticleNI EtherCAT driver for NILRT (niecati210k)
Hi, (sorry I also posted in NI Linux RT discussion) Still in the process to find alternatives to the discontinued Industrial Controllers ... I try to install the ni-ethercat-driver-dkms on a custom...
View ArticleEcoflow Monitoring and Control in LabVIEW
I recently purchased a Smart Home Panel, Solar Panels, and Battery Backup system from Ecoflow. Their system is accessible via my WiFi network through their mobile phone app. I love the system but the...
View ArticleCANopen interface Card PXI 8531 need and external CAN interface
I have LabVIEW code written for CAN interface module PXI 8461. when I use Same code for PXI 8531, its is not functioning as same.-> I'm not able to configure the PXI 8531 in NI MAX.-> When wrote...
View ArticleKeyence LRW and NU-EP1
I am trying to do external training from an HMI with a control logix processor. Does anyone have any sample code for the message instructions to accomplish teaching and bank selection?
View Article